Michael Jordan – Page 4 – Wise Photographer

You just pulled your lens out of the bag after a few weeks in storage, and out of habit you give it a little shake near your ear. There's a rattle. Maybe even a soft clunk when you tilt it one way and then the other. Your stomach drops a little, because a rattling lens sounds like a broken lens. So what's actually going on in there, and should you be worried? In most cases, no. A bit of rattle or clicking from a camera lens is completely normal and doesn't mean anything is broken. Keep reading to find out more. We'll go through what's usually moving around inside a lens when it makes noise, which sounds are just part of how the lens works, and the handful of situations where a clicking or rattling lens really does need a repair. Why Is My Camera Lens Making A Clicking Or Rattling Noise? Lenses are full of moving parts: aperture blades, autofocus motors, zoom mechanisms, and in many cases an image stabilization unit that floats a lens element on tiny electromagnets. When the lens is off, several of those parts have nowhere to lock into place, so they shift when you move the lens. Here are the most common causes, from completely harmless to genuinely worth a repair shop visit. 1. Loose image stabilization elements. If your lens has built-in stabilization (Canon calls it IS, Nikon calls it VR, Sony calls it OSS), there's a floating lens element suspended by small springs and magnets. When the camera is off, that element isn't being held in place electronically, so it can slide slightly and rattle when shaken. This is one of the most common reasons people panic over a "broken" lens that's actually working fine. Turn the camera on and the rattle usually disappears because the stabilizer locks the element in place. 2. Aperture blades resetting. You may hear a soft clicking sound when you mount or remove a lens, or right after you turn the camera on. That's the aperture blades snapping open and shut to their default position, and on some bodies they'll also click during autofocus as the aperture adjusts for each shot. Totally normal mechanical behavior. 3. Telescoping zoom barrels. Kit lenses and other zooms that physically extend when you zoom in often have some play built into the barrel so it can slide smoothly. A gentle rattle when you shake an extending zoom lens, especially at the wide end, is usually just that mechanical tolerance and not a fault. 4. A loose or cracked internal element from a drop or impact. This is the one that actually matters. If the lens was dropped, knocked against something hard, or has been rattling since an impact, an internal glass element or its retaining ring may have come loose. This usually shows up alongside blurry or soft images, or a visible tilt in one part of the frame. 5. Sand, dust, or grit inside the barrel. If you've been shooting at the beach or somewhere dusty and the zoom or focus ring has been moving through fine debris, that debris can work its way inside and cause a gritty rattling or grinding feel when you turn the rings. Worry not, this is fixable, but it does need a proper cleaning rather than being left alone. 6. A worn or failing autofocus motor. Older lenses, or ones that have autofocused hundreds of thousands of times, can develop a clicking or grinding noise specifically while hunting for focus. If the clicking only happens during autofocus and gets louder or more frequent over time, the motor itself may be wearing out. Not sure which one applies to your lens? This table breaks down what to listen and look for. Symptom Likely Cause Quick Fix Soft rattle only when camera is off, gone when powered on Floating stabilization element (IS/VR/OSS) None needed, this is normal Click when mounting the lens or turning the camera on Aperture blades resetting None needed, this is normal Light rattle in an extending zoom barrel Mechanical tolerance in the zoom mechanism None needed unless it worsens suddenly Rattle appeared right after a drop, plus blurry photos Loose or displaced internal element Stop using the lens and get it inspected by a repair shop Gritty, grinding feel when zooming or focusing manually Sand or dust inside the barrel Professional cleaning, don't try to blow it out yourself Clicking or grinding only during autofocus, getting worse Worn autofocus motor Have the motor tested and possibly replaced Also Read: How To Fix A Stuck Camera Lens? If you want to see and hear the difference between a normal rattle and a genuinely broken lens side by side, this short is a quick, practical watch. Frequently Asked Questions Is it normal for a lens to rattle when I shake it? Yes, for many stabilized and zoom lenses a light rattle is completely normal. It usually comes from a floating stabilization element or the mechanical play in a telescoping zoom barrel, not from damage. Why does my kit lens rattle more than my prime lens? Kit lenses are typically zooms with a telescoping barrel and built-in stabilization, both of which add moving parts that can rattle slightly. Prime lenses have a fixed focal length and often no extending barrel, so there's simply less inside them to move around. Can a rattling lens still take sharp photos? In most cases, yes. If the rattle comes from a stabilization element or normal mechanical play, image quality won't be affected. If the rattle showed up after a drop and your photos have gotten noticeably softer or unevenly blurry, that's a different story and the lens should be checked. Should I send a rattling lens in for repair? Only if the noise came with a specific event, like a drop or exposure to sand and water, or if your photos have gotten worse. A lens that has always rattled slightly and still shoots sharp images doesn't need to be sent anywhere. Will shaking my lens to test it damage anything? A gentle shake to check for rattle won't hurt a lens. Just don't shake it hard or bang it against anything, since that's how you'd actually cause the kind of damage you're trying to rule out. Final Words So, is a clicking or rattling camera lens something to worry about? Usually not. Most of the noise you'll ever hear from a lens comes from stabilization elements, aperture blades, or normal mechanical play in a zoom barrel, all of which are just part of how the lens is built. The exceptions are rattles that show up right after a drop or that come paired with gritty, grinding movement, and those are worth a trip to a repair shop. Next time your lens rattles, take a breath before you assume the worst; there's a good chance it's just doing exactly what it's supposed to do.